TEN-HIGH 60W CO2 Laser Tube 1000mm D50mm, Wires Preconnected with Coating, for Laser Cutter Laser Engraving Cutting Machine

Flаѕh Dеаlѕ - 50% оƒƒ TEN-HIGH 60W CO2 Laser Tube 1000mm D50mm, Wires Preconnected with Coating, for Laser Cutter Laser Engraving Cutting Machine Simple review

So you can check out the other reviews at Amazon.com

only with $

• ★ Power: 60W; Length: 1000mm; Diameter: 50mm; Item includes: 1 x tube.
• 【Wires Pre-Connected】For easy installation, the high voltage end and low voltage port have been connected in advance. If any support needed when installing, feel free to contact us.
• 【Quality Assurance】Each tube is tested before shipping and we will provide a safe packaging. If any problem after receives the tube, do let us know. We are willing to provide the best services and will provide 3 months warranty (except man-made damage).
• 【Advantages】All of our tubes are coated with nano gold catalyst, compared to non-coating one, its power increase about 7-20W. Uses TEMOO mode for output, high spot concentration, higher energy and more stable power. Apply unique glass metal sealing technology, and ensure a longer service life.
• 【Application】This CO2 laser tube is mainly used for laser cutter or laser engraving machine, which can carve and cut acrylic, cloth, leather, bamboo, wood, engraving, etc.

---

Product Description

Attention

1. Before placing order, please confirm the Diameter and Length of the laser tube. (Please make sure your machine has enough installation space, all should be a little bigger than laser tube's size.)
2. Each tube has been tested and we will provide a safe packaging. If there’s any problem after you received the tube, do tell us. We Don’T Want Our Customer To Waste Their Time And Money, and willing to provide the best services.
3. Laser tube is consumable, a long-time storage may lead to power attenuation. Thus, we recommend to buy it when you need to use, and after receive the tube, test it first. If there any problem, let us know in time, and we will provide after-sales services for free within 3 months. We Are Always Responsible For Our Products.
4. For engraving, it’s recommended to use machine of power below 80W. Because the diameter of laser beam is slender, which is more accurate. For cutting, machine of power above 80W is commonly used. Because the laser beam spot is bigger and more powerful.
5. If there doesn’t have the tube that you want or you have some special needs, feel free to let us know, so that we can customize for you.

Product Details

Length	1000mm (±10)
Diameter	50mm
Power	60W
Wavelength	10.6μm
Laser Beam Diameter	3-4mm
Mode	TEMOO
Package	1 pcs, 2.45KG

Working Current	15mA-18mA (Max 20mA)
Maximum output current	DC23mA
Input Voltage	AC90-120V / 200-240V
Working Voltage	20KV (Max DC28KV)
Trigging voltage	26KV
Response Time	＜1ms (from input to the output current reaches the nominal value)
Engraving Depth	0-6mm

Frequently Q&A

• Q: Is this tube compatible with my machine?
• A: We suggest to refer the Accessories List of your machine first, to confirm the DIAMETER, LENGTH and POWER of the tube. Size fits, compatible.

• Q: How does the product come packaged?
• A: Tightly embrace the laser tube with high-density sponge. Double foam rubber, Double boxed. We keep improving our packaging, listening patiently to the feedback form our customers. If there any problem caused by transport, we will be responsible for it.

• Q: Storage?
• A: Laser tube is consumable, which means that a long-time storage may lead to power attenuation. Thus, we recommend to buy it when need it. After receive the tube, test it first. If there any problem, let us know in time, we will provide 3 months after-sales services for free.

• Q: Difference between glass head and metal head?
• A: The power is the same and does not affect the use. The glass head has higher adhesion at both ends (especially in cold areas), better connection, less gas leakage, which ensure a longer services life.

• Q: How about the wiring method of the two ends?
• A: Wrap the metal wire on the carbon rod, fix it tightly with solder, then put on the insulating tube, and finally pour 704 glues into the tube.

• Q: How to insulate the high-voltage end?
• A: 1) As mentioned in the previous QA, after putting on the silicone tube, pour 704 glues inside. 2) Wrap a few more turns with electrical tape.

• Q: Power weak? Died too soon?
• A: Please let us know in time, we will send a replacement for free within 3 months.

• Q: Beam does not exit Tube?
• A: It may because of some incorrect operating of the laser machine. Feel free to let us know, to get some support.

• Q: Size of the water hose for inlet and outlet?
• A: Tube of Diameter 7mm x 11mm (0711), or of Diameter 6mm x 8mm (0608). (0711 is better because it’s thicker.)

• Q: What choice TEN-HIGH Laser Tube?
• A: We have more than 7 years of solid experience in laser industry, and are the earliest seller of CO2 Laser Tube. Over the years, we keep improving our product quality, as well as its packaging, according to customer’s feedbacks. Our aim is to create value for our customers and always be responsible for the products we sell. We are your trusted partner for laser accessories.

After coating, the laser power can be increased at least 5%. (Compared to non-coating tube)

Installation Steps

1. Determine the Positive and Negative poles of the laser tube. (the end with the spiral inside is the positive end)
2. Connect the positive end and negative end with the machine's wires correspondingly. (Pay more attention to the insulation, especially the high-voltage end, you can wrap with electrical tape a few more turns, or seal with 704 silicon rubber.)
3. Please Connect the Cooling Water Pipe. Feed water from the positive pole, the negative pole is out of water. Put the inlet and outlet water pipes into water, keep the water inlet under the laser tube and the interface cannot be leaked. Circulating water cooling, at least 20L. Before use, the water reservoir must be filled with water. (The laser tube has 3 layers in total. The innermost layer pass laser, the outermost layer is filled with CO2, and the middle layer is for the cooling water. There must be no water in the innermost and outermost layers.)
4. Adjust the optical path with the laser and test switch on the machine, to make the laser point enter from the middle of the entrance hole of the laser head, and then adjust the vertical optical path. (If the power is weak, try to wipe the lens at first.)

Maintaining Suggestion:

1. Confirm whether the water circulation works well every time before use.
2. Water temperature should be controlled at 20℃-30℃.
3. The laser tube is made by glass, which is fragile. Thus, be careful when installing and using it.
4. Avoid the dust accumulation nears to the high voltage electrode, keep it dry and clean, and keep the high voltage end away from the metal as much as possible. Otherwise, it may cause damages to the mainboard.
5. The cooling water should be replaced in time:

• Summer: Replace the water every 2 weeks at least (you can put some ice in the water for cooling down);
• Winter: replace the water every 4 weeks at least (do not let the water freeze);
• The higher the machine power is, more often need to replace the water.

Positive pole: The positive pole is the high-voltage end, connect with the positive terminal of the machine and the inlet water pipe, to feed cooling water in. (Pay more attention to the insulation, especially the high-voltage end, you can wrap with electrical tape a few more turns, or seal with 704 silicon rubber.)	Negative pole: The negative pole is out of water, connect with the negative terminal of the laser machine. (Make sure that the inlet is lower than the outlet.)	Easy installation: Wire preconnected: the wires of the two ends, positive pole and negative pole, are connected in advance. Just connect with the wires of your laser machine correspondingly, then make sure the insulation. If any question during installing, feel free to let us know.

Read more

	ZnSe Focal Lens	GaAs Focal Lens	Mo Reflective Lens	K9 Gold-Plated Glass Reflective Lens	Laser Power	Upgraded Laser Tube
Diameter	12/15/18/19.05/20/25/25.4mm	18/19.05/20/25/25.4/28mm	20/25/30mm	20/25mm	None	None
Focal Length	25.4/38.1/50.8/63.5/76.2/101.6/127/190.5 mm	50.8/63.5/76.2/101.6/127mm	None	None	None	None
Wavelength	10.6um	10.6um	10.6um	10.6um	10.6um	10.6μm
Power	30W-400W	100W-600W	40W-100W	40W-50W	40/50/60/80/100/150W	Please refer to Product Details
Coating	✓	✓	X	✓	✓	✓

---

Product information

Package Dimensions	45.35 x 7.32 x 7.28 inches
Item model number	TH-60WCO2LT1000
ASIN	B01N012STA
Customer Reviews	4.3 out of 5 stars 324 ratings 4.3 out of 5 stars
Best Sellers Rank	#100,927 in Arts, Crafts & Sewing (See Top 100 in Arts, Crafts & Sewing) #95 in Power Milling Machines #236 in Jewelry Making Engraving Machines & Tools #2,210 in Craft Cutting Tools
Is Discontinued By Manufacturer	No
Item Weight	4.85 pounds
Manufacturer	TEN-HIGH
Date First Available	November 5, 2016

Chесk Hеrе : ➲➲

----------------------------

Hеу mу brо, Mаnу thаnkѕ fоr vіѕіtіng оur Wеbѕіtе. Arе уоu сurrеntlу trуіng tо fіnd fасtѕ аbоut TEN-HIGH 60W CO2 Laser Tube 1000mm D50mm, Wires Preconnected with Coating, for Laser Cutter Laser Engraving Cutting MachineThе Gооd Nеwѕ, Rіght nоw wе'rе gіvіng bіg аѕ muсh аѕ 85% fоr реорlе whо buу TEN-HIGH 60W CO2 Laser Tube 1000mm D50mm, Wires Preconnected with Coating, for Laser Cutter Laser Engraving Cutting Machine рrоduсtѕ thrоugh thіѕ Wеbѕіtе.Nоt јuѕt thаt, уоu'll еvеn gеt уоurѕеlf а аbѕоlutеlу frее dіѕсоunt іn thе еvеnt thаt уоu оrdеr tоdау.Thаnkѕ fоr wаtсhіng аnd рlеаѕе gіvе а thumbѕ uр.

----------------------------

Disclaimer:

Thіѕ Wеbѕіtе іѕ раrtісіраnt іn thе аmаzоn ѕеrvісеѕ llс аѕѕосіаtе рrоgrаm.I dо uѕе аffіlіаtе lіnkѕ whеn lіnkіng рrоduсtѕ іn thе Wеbѕіtе dеѕсrірtіоn.Thіѕ dоеѕ nоt аffесt уоur buуіng еxреrіеnсе оr іtеm рrісе but dоеѕ mеаn I rесеіvе а ѕmаll соmmіѕѕіоn оn іtеmѕ рurсhаѕеd uѕіng ѕuсh lіnkѕ.An аffіlіаtе аdvеrtіѕіng рrоgrаm dеѕіgnеd tо рrоvіdе а mеаnѕ fоr ѕіtеѕ tо еаrn аdvеrtіѕіng fееѕ bу lіnkіng tо wеbѕіtе аnd аmаzоn.соmWе аlѕо раrtісіраtеѕ іn аffіlіаtе рrоgrаmѕ wіth оthеr ѕіtеѕ. Wе аrе соmреnѕаtеd fоr rеfеrrіng trаffіс аnd buѕіnеѕѕ tо оthеr соmраnіеѕ.

---------------------------

Tweet